BYD ATTO 3 Roof Rack
Friday, 13 November 2026 4:25:45 pm Pacific/Auckland
Quick answer: the BYD Atto 3 comes with flush roof rails, so it takes our Flush Rail Roof Rack. Order one Model D bar (94.5 cm) for the front and one Model C bar (90.5 cm) for the rear. The bars are $90 each, so a full set for the Atto 3 is $180, and fitting takes 10 to 20 minutes with no drilling.

Why the Atto 3 needs two different bar sizes
The Atto 3's roof rails sit flush against the roof, with no gap underneath, and they are not parallel. The roof narrows towards the back of the car, so the distance between the rails is larger at the front than at the rear. A pair of identical bars would leave one of them either too long or too short.
Our flush rail bars are sold individually for exactly this reason. You pick the size for each position:
| Position on Atto 3 | Model | Bar length | Fits rail inside distance |
|---|---|---|---|
| Front bar | Model D | 94.5 cm | 101–105 cm |
| Rear bar | Model C | 90.5 cm | 97–101 cm |
Each bar has 4 cm of adjustment built into the feet, which is what lets it clamp tightly against the inside edge of the rail.
What you get
- Material: high-strength aluminium alloy, black finish
- Bar profile: aerodynamic, 7.5 cm wide, shaped to keep wind noise down
- Load rating: Rated 50 kg per bar (100 kg for a pair). Never exceed your vehicle's roof load limit in the owner's manual – whichever is lower applies.
- Mounting: clamps onto the factory flush rail, with no drilling and no changes to the car
- Carries: roof boxes, bike racks, ski racks, kayak and boat carriers
- Price: $90 per bar ($180 for the Atto 3 set of two)
One thing specific to an EV: anything on the roof adds drag, and drag costs range. A low, aerodynamic bar costs less range than a square one, and taking the bars off when you are not using them for a few weeks costs nothing at all. They come off as quickly as they go on.
How to install the roof rack on a BYD Atto 3
- Measure first. With a tape measure, check the inside distance between the two rails where the front bar will sit and again where the rear bar will sit. You should get a figure in the 101–105 cm range at the front and 97–101 cm at the rear.
- Clean the rails. Wipe off dust and grit where the feet will clamp so the rubber pads sit flat and do not mark the rail.
- Place the front bar (Model D). Loosen the feet, lay the bar across the roof and seat both feet onto the rails.
- Place the rear bar (Model C). Do the same further back. If you are fitting a roof box, check its instructions for the bar spacing it needs before you tighten anything.
- Centre each bar. Make sure the overhang is the same on the left and right sides.
- Tighten evenly. Tighten the left and right feet a little at a time, alternating sides, until both clamps grip the rail firmly.
- Test it. Grab each bar and push and pull hard in every direction. Nothing should move. Check the clamps again after your first drive.
The whole job takes 10 to 20 minutes. The product page has the installation diagram and a real fitting example.
Frequently asked questions
What size roof rack fits a BYD Atto 3?
Model D (94.5 cm) at the front and Model C (90.5 cm) at the rear, from our flush rail roof rack range. The roof tapers, so the two bars are different lengths.
How much does a roof rack for the BYD Atto 3 cost?
$90 per bar, so $180 for the pair.
Do I need to drill or modify the car?
No. The feet clamp onto the factory flush rails and come off again without leaving anything behind.
How much weight can I carry?
Rated 50 kg per bar (100 kg for a pair). Never exceed your vehicle's roof load limit in the owner's manual – whichever is lower applies. Remember that the weight of the bars and the roof box counts towards it.
Can I put a roof box on an Atto 3?
Yes. The bars take standard U-bolt and clamp-style roof box fittings. Have a look at our roof box range when you order the bars.
Can I get it fitted in Auckland?
Yes. Bring the car to our workshop at Unit 14/77 Porana Rd, Glenfield, and we can check the fit on the spot. We also ship nationwide from Auckland.
Order your BYD Atto 3 roof rack
On the Flush Rail Roof Rack page, add one Model D (94.5 cm) and one Model C (90.5 cm) to your cart. If your Atto 3 has had its rails changed, or your measurements come out differently from the table above, get in touch before ordering and we will match the right sizes for you.
